Page 1 of 2 12 LastLast
Results 1 to 10 of 12

Thread: Hides/Skins

  1. #1


    Does anybody do anything with their skins after they have removed them from the deer. I was wondering if you have any tips on how to prepare them, i.e clean and traet them poss to use as rugs or if the beast has a fine coat just to keep it for sentimental value?

  2. #2

  3. #3
    Quote Originally Posted by 300wsm
    You can tan them with Diesel and Bicarb of Soda I will try to dig out the instructions for you.
    They look good but foam at the mouth and stink like an old landrover!!!

  4. #4
    There must be a cheaper way than using diesel


  5. #5
    Buy some borax from the chemist and soak it in that for a bit. This is the stuff my mate uses for tanning skins before he does his taxidermy, if softens it.

    I personally do some training with the dog.

    I have often thought about tanning a red deer skin with the head still on for the living room, but after plenty of thought i reckon i would keep tripping over the antlers


  6. #6
    Would love a barrel at the allotment full of skins!. So all the experts out there , how do we do it on an amateur basis , heard of adding oak leaves for the Tannin, scraping etc ! So how Do we get a usable pelt!!! That ain't shedding Hairs! Any Inuits out there, OR INJUNS!! A fair question.
    Regards Trapper

  7. #7
    i tried curing a french partridge skin but the local chemist told me i was no longer allowed to buy borax and that it was illegal . so i used some nail varnish remover to get rid any fat etc and left it in the garage unfortunately a little too long and it went too stiff to mount onto a mold .
    hope you have better luck mate

  8. #8
    I tan my decent fallow hides using the following instructions:

    You can get alum and borax from a chemical supply company, its not illegal.
    Soda/salt(discwasher) fron Tesco

    I finish with tanning oil from I think Attleborough


  9. #9
    Sorry to say I have never heard of tanning a deer skin with Diesel, I suspect it would work but if you want to tann a deer skin, borax and alum is also not tanning, that is curing.

    To tan a deer skin properly you need to go through several stages, and different tans give different results. For instance most rugs for floors, similar to sheep skin rugs, are Chrome Tanned, this shrinks the pelt slightly giving a denser feel and the distinctive blue grey colour sometimes on the back. This tan is useless for Taxidermy purposes.

    1. Remove all fat, meat and sinew from the skin.

    2. Wash the skin thouroughly in warm water with biological washing powder. This will release all the blood and dirt from the skin and also some of the grease.

    3. Rinse in cold water and drain.

    4. For every 3lbs of dry skin weight, mix 7galls of warm water, with 6lbs of salt, and 7.5oz of Formic Acid. (note wear gloves and goggles be careful) make sure its in a plastic dustbin or container, dont use metal.
    Punch the skin into the solution and make sure you have all the air pockets out, otherwise bacteria will live in the air pocket and the skin may slip. Leave in the solution for two or three days. You will notice it turns the flesh white.

    5. Take out of solution and drain, once drained you can thin the skin down on a machine or by hand with a knife, as you will find the fixing of the skin has plumped up the pelt. You can return it back to the solution as much as you like but ensure the acidity does not drop otherwise the skin may slip.

    6. Buy yourself some Lutan FN tanning powder, or a Ktan tanning kit. I use Lutan FN, and after fixing the skin I then mix 7galls of warm water, 3lbs of salt, 40z of Bicarb, and about 7oz of Tanning oil, plus 12oz of Lutan FN Tanning Powder. Mix it up and drop the skin back in and punch it into the mix to release any air pockets. Go back every 15 minutes for the next hour and stir and punch the skin into the solution with a large stick. Leave for about 2 days.

    7. Take out and drain, and dry by stetching out the pelt, when it is damp mix up some Tanning Oil with warm water 60/40 and paint onto the skin, and let it dry. When the skin is dried you will be able to stake it over a wooden pole.

    8. Staking measn breaking the fibres up, and as you work the skin on the flesh side you will notice that it breaks down into a fluffy texture and soft. You have tanned your skin!!

    Any other method with just salt, borax (which makes the skin hard) is curing not tanning, the skin will rot if it gets wet over a period of time. And it will not be soft and supple.

    Good luck.

  10. #10

Similar Threads

  1. taxidermist needed to tan and export skins for mouting to Au
    By aussie hunter in forum Taxidermy & Trophy Preparation
    Replies: 4
    Last Post: 08-08-2010, 23:42
  2. For Sale Fox Skins/Pelts
    By nielaj in forum Deer Stalking Equipment
    Replies: 5
    Last Post: 23-02-2010, 21:14
  3. WANTED Fallow deer skins
    By ash243 in forum Deer Stalking Equipment
    Replies: 2
    Last Post: 02-02-2010, 20:50
  4. Tanned skins
    By kingstonandy in forum Deer Stalking General
    Replies: 12
    Last Post: 05-01-2009, 21:48
  5. Portable hides
    By Kent in forum Equipment & Accessories
    Replies: 0
    Last Post: 07-11-2007, 12:29

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts