Results 1 to 10 of 10

Thread: Loose shotgun stock - Browning

  1. #1

    Loose shotgun stock - Browning

    My luvly Browning Ultra XS has developed a loose stock. Won't be shooting it again until I tighten it back up.

    I've taken off the butt pad and looking down the hole I can see the head of the bolt way down there that secures the stock to the action. (who the heck designed that then?)I

    've tried getting it with an extended hex head socket wrench with no luck and doesn't look like its a slot or screw head on it.

    Any ideas how to tighten the beggar up?

    Jim
    I never make the same mistake twice.

    I make it five or six times.

    Just to be sure.


  2. #2

  3. #3
    My 525 is a slotted screw and I keep a long big screwdriver for the job. Also keep a length of copper pipe (2" long) to drop down over the screw head so that if the screwdriver slips it wont go through the stock.

    David.

  4. #4
    Hi, I had the same problem. Go to Wickes and get the longest flat head screwdriver they have - and they have some whoppers! when you get it out find a couple of washers that will fit and use them when you replace it so you can get it nice and tight.

    Alternatively, I had a couple made from high grade stainless steel, but with hex heads and much easier to locate and get out, plus better quality than the original - cost was about 20 including postage. You just need to work out what the thread is on the existing one.

    I like the copper pipe idea - that would have saved me some frustration and fiddling around!

  5. #5
    Thanks folks - will attempt to overcome this challenge.....
    I never make the same mistake twice.

    I make it five or six times.

    Just to be sure.


  6. #6
    SD Regular
    Join Date
    Dec 2008
    Location
    East Midlands M1/M69 Junction 21
    Posts
    6,213
    Keeping guns in "dry as a bone" centrally heated houses is as bad for their stocks as is keeping guns in damp condensation prone houses is for their metalwork. It's finding the balance.

    And bad for antique wood chairs, tables, bookcases etc., etc..

    A gun cabinet shouldn't be damp but it also should be so "dry" as to cause stock shrinkage....but properly seasoned wood shouldn't, suposedly, anyway. But if your gun room is really dry even that will.

    Once it's tightened...I used to have a big "f**k off" 1/2" square shaft slotted head screwdriver for Enfields you could put mole grips on and everybody wanted to buy it...turn your heating down two degrees.
    Last edited by enfieldspares; 05-12-2016 at 15:35.

  7. #7
    Quote Originally Posted by JockStalk View Post
    Thanks folks - will attempt to overcome this challenge.....
    I got as far as getting the buttplate off my browning and seeing how deep that screw was recessed. I never did buy a LONG screwdriver, but probably should at some stage to do a bit of maintenance.

  8. #8
    Jim, take it to my old boy at Seals Cove, he'll get it sorted for you. I'd do it myself if I was at home, but that won't be for another ten days or so.

  9. #9
    I never make the same mistake twice.

    I make it five or six times.

    Just to be sure.


  10. #10
    Followed Malxwal's advice.
    All sorted. Turns out a batch of ultras were supplied with hex5 head stock bolts. A 3 extender bar for my socket and hex set sorted the problem.
    Happy days.
    I never make the same mistake twice.

    I make it five or six times.

    Just to be sure.


Similar Threads

  1. Stock - rosewood forend loose
    By JockStalk in forum Cleaning, Gunsmithing and Equipment Care
    Replies: 28
    Last Post: 02-09-2015, 10:52
  2. *SOLD* Browning O/U shotgun case
    By jcampbellsmith in forum Other Shooting Equipment
    Replies: 1
    Last Post: 31-01-2015, 11:54
  3. Browning shotgun
    By chris .222 in forum Other Shooting & Keepering
    Replies: 2
    Last Post: 06-03-2014, 09:24
  4. Browning A5 shotgun
    By simon1979 in forum Rifles & Calibres
    Replies: 10
    Last Post: 02-11-2013, 18:02
  5. Loose Shotgun
    By Wilf102 in forum Cleaning, Gunsmithing and Equipment Care
    Replies: 4
    Last Post: 09-01-2013, 23:54

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •