Page 1 of 3 123 LastLast
Results 1 to 10 of 21

Thread: Jammed Moderator

  1. #1

    Jammed Moderator

    Any one got any ideas on how to unscrew a jammed bridge section of a wildcat predator mod ? Currently got it soaking in diesel. Really frustrated.
    Those who can, do it. Those who can't, teach it.

  2. #2
    ultrasonic cleaner and penetraing oil if you can find one big enough

  3. #3
    Rubber bands
    Below is a link to my website.
    Quad sticks

  4. #4
    Try boiling water or put it in the freezer and when its cold enough then use boiling water.

    Or maybe in this order would be better, put it in boiling water until it heats then remove to the freezer for 5/10 mins they try it. I think that's what has worked for me with various items threadlocked that I would have risked damage with direct heat ie blowtorch worth a try bud.
    Last edited by dlz90; 17-09-2014 at 17:27.

  5. #5
    Try this - Loctite Freeze and Release Penetrating Oil. About 8.00 a can used it on weathered nuts and bolts with great results.

  6. #6
    Rustola or heat it up in oven gas mark 3 then use a oil filter tool to remove it then keep it oiled ?

  7. #7
    Quote Originally Posted by paul o' View Post
    Rustola or heat it up in oven gas mark 3 then use a oil filter tool to remove it then keep it oiled ?
    copperslip on the threads, and next time buy a one piece mod that doesnt have to be stripped
    "Politicians must be allowed to panic. They need activity. It is their substitute for achievement"
    "'The matter is under consideration' means we have lost the file. 'The matter is under active consideration' means we are trying to find the file."

  8. #8
    Add some ATF (automatic transmission fluid) to the diesel and you'll have the best penetrating oil going.


  9. #9
    good evening Richard, one of the best "release agents " we have found ,and we use in the workshop is a 50/50 mix of acetone and automatic transmission fluid. It seems to work very well and gets into even badly rusted / seized parts. A word of warning though ,the flash point for this liquid is VERY low, so do not smoke or have a naked flame any where near it. Normally soaking for 48-72 hours sees the job done in most cases. Any way good luck . Yours respectfully Mike Norris Brock and Norris Custom Rifles

  10. #10
    Add the same again in equal amounts (50/50) mix of kerosene & varsol (mineral spirit) to the acetone & transmission fluid....and you've got a very effective bore cleaner known as "Ed's Red"

    Atb, Buck.
    Last edited by Uncle Buck; 17-09-2014 at 21:24.
    "let him without sin cast the first stone"

Similar Threads

  1. Jammed .223 round ?Why
    By Cyres in forum Ammunition, Reloading & Ballistics
    Replies: 61
    Last Post: 25-09-2014, 12:53
  2. Winchester mod 70 safety catch jammed
    By corky in forum Cleaning, Gunsmithing and Equipment Care
    Replies: 11
    Last Post: 22-09-2013, 19:00
  3. GPS jammed in Scotland in April
    By caorach in forum Deer Stalking General
    Replies: 1
    Last Post: 26-03-2012, 11:45
  4. Help - Jammed semi auto s/g
    By scrun63 in forum Cleaning, Gunsmithing and Equipment Care
    Replies: 20
    Last Post: 12-02-2012, 21:59
  5. Help case jammed
    By buckup in forum Ammunition, Reloading & Ballistics
    Replies: 14
    Last Post: 22-10-2011, 00:21

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts