tikka t3x

  1. Sold: Tikka T3X roughtech rifle .308win with extras cheap

    Tikka T3X roughtec .308win rifle Good condition, sub 300 rounds. Can send bore scope pics if required. - 20" threaded blued fluted barrel with 1 in 11 twist. Threaded 5/8 UNEF. - Leupold QR bases and 30mm blued high rings. -Fluted bolt. -Aftermarket Sterk bolt handle. -Stock is synthetic, is...
  2. For Sale: Tikka T3x Roughtech 243win

    Hi all, I’ve decided to sell my Tikka T3x Roughtech 243win. Looking to get £1100 for her and accessories. These seem to be retailing for £1500. (T3x Lite Roughtech Fluted Rifle) ***Scope not included *** • Fluted barrel • Fluted bolt • Threaded 5/8 x 24 • Tikka muzzle break • Tikka steel...
  3. Sold: Tikka T3 Accessory Job lot

    Tikka T3 bottom plastic, T3 bolt shroud and now only one set of original T3 action screws (different to photograph), two steel T3x recoil lugs. All original parts and usable on T3 or T3X models, regardless of cartridge.(bottom plastic is only applicable to stocks and not chassis's) £40 posted...
  4. Swap: Tikka t3/t3x mdt hs3 chassis. Left hand.

    I have an left handed mdt hs3 LA Tikka chassis that im looking to swap for a lighter chassis, I would keep the stock and pistol grip. If anyone has anything they want to swap send me a pm and we can discuss. I would be open to other adjustable stocks (if swapping for a complete stock obviously...
  5. Sold: Tikka T3X Carbon Fibre boyds stock, magazine and bottom plastic guard. £210

    FOR SALE A S/H Tikka T3/ T3X right handed Boyds thumbhole stock that has be well prepped/primed and then carbon fibre hydro-dipped and gloss coated for shine and protection. Steel recoil lug fitted. 3 stock studs fitted as standard. I have used it on a 243 for a few years, so its had some...
  6. Caveat Emptor - Tikka T3X Lite Wideland Veil Rifles

    As I previously posted here I bought a new .308 Tikka T3X in Wideland Veil cammo from Braces of Bristol in May 22. Back in September, I became concerned by the loss of Cerakote from just inside the receiver and along the bolt raceway (see below). I took the rifle back to Braces and they kindly...
  7. Introduction

    Hi folks, I'm joining the site because I have found a lot of useful information on here whilst doing some research with the old .270 or .308. Wont go into that as its a can of worms. I have been deer stalking Roe for the past 16 years in mainly woodland and semi urban areas in Lanarkshire. Only...
  8. Tikka T3X Lite Wideland Veil Cerakote Problem

    A question please for those who also have a T3X Lite in Woodland Veil and for those with Cerakoting experience. In May of this year I bought a brand new T3X Lite in Woodland Veil; 20" .308. The short story of why I ended up with this rifle is that I wanted a lightweight .308 rifle with a 20"...
  9. Wanted: GRS Hunter Light - T3x

    I'm keen for one of these on my T1x (with a bit of fettling), ideally in brown, but will consider others. Are there any out there in the second hand market before I order one at full whack? Thanks in advance.
  10. Optilock or picatinny?

    So I’ve just bought a Tikka T3x Roughtech in 243. I’ve always mounted my scopes using the tried and tested picatinny system. However, some people have been suggesting using Optilock … what’s everyone’s thoughts?
  11. Tikka T3X TAC A1

    Okay so, I have had my Tikka for a while now and quite frankly I love it; it's a T3X TAC A1 chambered in .260 Rem still with the factory barrel. I am starting to change some things around with the rifle and playing with new loads - something had to keep me busy during lockdown anyway! I have...
  12. Manners MCS-EHT/EHTA for Tikka T3X

    Hi All, I'm looking to replace the factory stock on my Tikka T3X Varmint. I'd like a stock rather than a chassis (i think). I've been looking at a Manners MCS-EHT / EHTA. Has anyone got any experience with these stocks? Good? Bad? Finally does anyone know where you can buy them from in the...
  13. Tikka T3x lite barrel diameter

    Hi can anyone tell me the diameter of the barrel of a Tikka T3x lite 308 just behind the 14x1 thread? Many thanks, Chris.
  14. Filling Tikka T3X Stock

    I have a Tikka t3x Varmint in 308, the butt end of the stock is filled with a factory supplied foam insert, but it still feels light and hollow. I was thinking of removing the factory supplied foam insert and replacing it with something heavier / more dense. Has anyone else done this? Any...
Back
Top