Colouring a heed

JH83

Well-Known Member
I have a head I’d like to strip the velvet (it was already slightly peeling so fully formed) and colour up. I have used potassium permanganate before and it’s alright but not amazing in my book.

Any other methods that spring to mind?
 
There are proprietary antler stains on the market, believe bushwear sell knoblock or whatever it’s called, JHT supplies also stock something.
P permanganate works well, as long as you’re patient in layering it up and the head then never gets exposed to moisture (ie only indoors not on an outside wall) as it runs like buggery.
Tried things like tea and coffee with very poor results.
 
There are proprietary antler stains on the market, believe bushwear sell knoblock or whatever it’s called, JHT supplies also stock something.
P permanganate works well, as long as you’re patient in layering it up and the head then never gets exposed to moisture (ie only indoors not on an outside wall) as it runs like buggery.
Tried things like tea and coffee with very poor results.
I have a tub of it that I've debated on using I use quite a bit of spray products just to keep room smelling nice and fresh and I'll often hit my antlers and sorts since antlers, especially fresh ones have an Oder to them, I imagine it would rehydrate and cause it to run? not to mention Its actually a fairly bad household chemical and no one talks about it, it reacts with quite a handful of things.

For antler I would always sand and try water based wood stains first a velvet antler it might actually work better since there usually more porous nailing antler colour is hard enough but the "gloss" of the oil based woodstain is pretty rough.

I regret staining this antler and I've half debated sanding it all off Its just ugly as hell sticks out like a sore thumb need an ebony based stain think this was walnut or oak.

1692790209548.png
 
Last edited:
The best stain is potassium permanganate crystals.

Mix with water and paint on.

View attachment 325662
View attachment 325663
I would also add it to the cornets and then work them and other “wear” areas with wire wool or light sand paper to get a more natural finish. Also with velvet antlers when stripped the antler below has lots of sharp raised bits which would naturally wear smooth with use, for a more realistic finish I’d knock those back too with sand paper
 
I would also add it to the cornets and then work them and other “wear” areas with wire wool or light sand paper to get a more natural finish. Also with velvet antlers when stripped the antler below has lots of sharp raised bits which would naturally wear smooth with use, for a more realistic finish I’d knock those back too with sand paper
That is what I did after it had dried, looks very natural. 👍🏼
 
I tried the walnut briwax tonight on the antler I posted above, there's some spots where it went "firey" red because of the old stain but overall I think it works pretty well. ?

It looks pretty natural and not daft at all now at least, I imagine with a stripped velvet antler it would work the best.
1692993992562.png1692994006789.png
 
Why try to fake it? Surely the memory of the stalk should be remembered for what it was? I personally don’t mind tatty mountings, what matters is they are relative to the time/experience.
 
I have a head I’d like to strip the velvet (it was already slightly peeling so fully formed) and colour up. I have used potassium permanganate before and it’s alright but not amazing in my book.

Any other methods that spring to mind?
Have you stripped the velvet?

I have one and I’m not sure how best to do it!
 
I’m letting nature do it’s work 🤣

I’ll try @deerstalker.308 recommendations 👍👍
Seriously last decent fallow I did was velvety all over, but questionable how well it would turn out, got the skull boiling away, allowing as much steam as possible to get on the antlers, then dipped them in turn for a few seconds just to blanch the tissue off, it peeled off like if you blanched tomatoes, so simple.
But, remember the antler is full of blood at this stage, so it needs to be hung upside down to dry, and prick the very tips of the antlers to allow the blood to drain out, they hold a fair bit, and you don’t want that staying, it’ll stink!
 
I coloured antlers by stripping velvet, got a bulk bag several shovels top soil,half bag potting compost,cut some branches out of apple tree then shreaded them.put all in bulk bag with the antlers and some water .
Tied up top of bag next morning antlers a nice colour .
I just thought about what deer rub there antlers on and tried that .
Really easy to do and cost nothing
 
  • Like
Reactions: VSS
The buck in question and the process
 

Attachments

  • IMG_1280.webp
    IMG_1280.webp
    438.3 KB · Views: 48
  • IMG_1282.webp
    IMG_1282.webp
    383.2 KB · Views: 47
  • IMG_1301.webp
    IMG_1301.webp
    179.4 KB · Views: 48
  • 188C9254-B3BB-43BB-88AD-B3DC00630778.webp
    188C9254-B3BB-43BB-88AD-B3DC00630778.webp
    187.8 KB · Views: 48
Back
Top